Dez Racing brought a simple...
Dez Racing brought a simple 11.50 car to Englishtown for some fun. We put it through a barrage of 60-foot tests to check consistency with and without an MSD Launch Control two-step rev-limiter.
Consistency is a term that applies as much to street/strip Mustangs as it does to all-out race cars. It's due to the trickle-down effect, and one such component to help anyone be more consistent in a street-oriented but strip-driven Mustang is a two-step rpm controller. It's a simple component that uses two rpm limits-a low-side and a high-side-to help launch consistency. The low side is used to limit launch rpm so you can floor the gas pedal and the revs won't go higher than the designated level. The second "step" is the high-rpm rev limiter, which does not replace the computer's rev-limiter, but is used in addition to it.
A majority of the Stangs we come across feature some type of lowering springs, shocks and struts that are either stock or tagged for general use, and a set of sticky drag radials. The cars feature a mix of comfortable riding and marginally better-than-stock performance. That combination of suspension and tires usually doesn't bode well for traction at the dragstrip. It's nearly impossible to leave the starting line with the tach needle in the stratosphere. This is where a two-step rev limiter will help you be more consistent and get the most out of your car. For those who participate in drag-racing competitions, a two-step will help you hit the Tree better by allowing you to focus solely on the lights and not worrying if the rpm is just right.
Our test pilot, Mike Dez,...
Our test pilot, Mike Dez, found the best launch rpm was at 3,500, thanks to a set of drag radials and a mostly stock suspension.
The problem with two-step rev limiters in modular motor applications has been the lack of a distributor and the difficulty of tying into the factory ignition. The new MSD Launch Control unit is specific for the Coil-On-Plug ignition system. Essentially, modular motors have a coil for each cylinder, which is charged/activated via the computer wiring harness. The MSD Launch Control interfaces with each coil and cuts spark to limit rpm. A separate activation switch (handheld button, clutch switch, micro-switch, and so on) is used to release the rpm limit and switch to the high-side limit. Of course, your Mustang has a factory rev limiter, but the stock unit cuts fuel to control rpm, where the MSD unit cuts spark. The latter is much safer, especially in forced induction or nitrous applications, where a lean condition can lead to engine damage.The installation is virtually plug-and-play, save for setting up the activation switch.
Mike Dezotell of Dez Racing volunteered to handle the install and subsequent track testing for this story. At the time we called the Seekonk, Massachusetts-based shop, Dez had just purchased a new shop car and was looking to test this two-step. The timing couldn't have worked out better for us. The new Dez Racing shop car is an '01 Mustang GT with a fortified bottom end, TEA-ported Two-Valve heads, Anderson Ford Motorsport F-42 camshafts, Ford Racing/Bassani exhaust parts, and a ProCharger P1SC (12 psi). The car also utilizes an Anderson Ford Motorsport Hi-Rev clutch, 3.73 gears, and a set of M/T Drag Radial tires. The innocent Two-Valve ride makes 464 rwhp and is as tame as a stocker. Dez estimated it would run mid-11s all day long in that trim, but with a stick shift and mostly stock suspension, he needed a two-step to be consistent.
We shipped the unit to Dez Racing, asked the guys there to get the part installed, and then meet us at Englishtown for some testing the following week. The goal was to evaluate 60-foot times and show the effectiveness of a two-step controller. When working off the tach, the driver is constantly looking and focusing on the gauge cluster. Dez says, "It's hard to hit the Tree and be consistent without a two-step. You're trying to watch the rpm and the Tree at the same time." Dez is an accomplished racer with championship titles in the NMCA racing organization. He's also a veteran in the NMRA Real Street category, which requires the use of a stick-shift transmission.
 Utilizing an MSD Launch Control...  Utilizing an MSD Launch Control device enables a driver to find the best launch rpm for his/her Mustang, and allows the driver to be consistent by leaving at the same rpm every time. Street cars benefit from a two-step because most of the time the car doesn't have a dedicated drag-race suspension, so tire spin at high-rpm launches is usually the result. Keeping the revs down, and doing it consistently, helps get the most from your Pony at the dragstrip. |  The kit is virtually a plug-and-play...  The kit is virtually a plug-and-play installation right out of the box. MSD built this two-step specifically for the mod-motor Stangs. |  The MSD unit has pigtails...  The MSD unit has pigtails that interface with the coil-on plugs and the computer wiring harness. Essentially, the MSD box intercepts the signal and cuts spark to limit the rpm levels. |