Lamotta then installed our new X-style mid-pipe from American Racing Headers, and connected it to the existing after-cat system. The kit from ARH also comes with extenders for the oxygen sensors. Lamotta then drained the oil from the transmission, and refilled it and the engine with AMSOIL fluids. This wrapped up the install. At about 1 a.m., Jake Lamotta hit the key and Superfly came to life. Though it hadn't yet been tuned, we could tell it was going to be an animal. Satisfied, we called it a night.
We reconvened on Monday and Chris Johnson of SCT Performance made the short trip across town from SCT's headquarters to Lamotta's to tune our new setup. SCT supplied us with a new X3 handheld tuner, and Johnson made the necessary adjustments to accommodate our new components. Taking into account the daily-driver status of this project, he burned one tune for everyday driving on the street and one for the track.
On the race tune, Superfly spun the rollers on Lamotta's Dynojet to a best of 428 rwhp at 6,100 rpm and 395 lb-ft of torque at 5,100 rpm--that's 68 rwhp more than the old engine on its best day, and at a usable point in the rpm range!
In the next few months, we'll sort out our input shaft issue, install the new clutch, and get Superfly out on track. We expect to break into the low-11s, only this time without the juice. We also have a couple of open track outings planned, so be on the lookout for those results as well.

6a Carrying over from the...

6a Carrying over from the engine dyno test is our ported Mach 1 intake manifold. This is much more capable of handling air delivery duties to our 323ci stroker than the stock '96-'98 Cobra intake on the outgoing engine...

6b ...However, we did have...

6b...However, we did have to make a few changes to accommodate it.

7 C&L Performance sent us...

7 C&L Performance sent us its '03-'04 Mach 1 MAF system and inlet pipe (PN 10699M1P; $369). The mass air meter housing was calibrated by C&L to work with a stock mass air meter and our new 34-lb/hr injectors.
Since we were now 70-rwhp higher than our best ever dyno run on the old engine, we knew that it was time for a clutch upgrade. We were using a stock Cobra clutch, and it has taken a beating. So we called Centerforce for one of its new DYAD DS twin-disc clutches. When it arrived, we were excited to say the least.
Here is the 10-spline input...
Here is the 10-spline input shaft on our old T-56. You can't even get a T-56 with a 10-spline input shaft anymore, and for good reason. The 26-spline input shaft is much stronger and capable of handling much more than our N/A Four-Valve could throw at it.
The DYAD DS is a multi-disc clutch designed to handle up to 750 lb-ft of torque, while maintaining daily-driven driveability. It offers smooth engagement, quiet operation, a light pedal feel, and an exceptional holding capacity. The only problem is that our old T-56 has a 10-spline input shaft and the DYAD that we ordered is for a 26-spline input shaft.
So when we discovered this problem, we called our main man at Centerforce, Will Baty. He informed us that he could send us a different disc, but it would be wasting our time and his. Why? He went on to say that our 10-spline input shaft would twist like a pretzel under heavy-duty driving conditions considering the output of our new engine.
So we figured we would call our friends at D&D Performance for an input shaft upgrade. Over the phone, Don Walsh Sr. asked us about the First gear ratio for our T-56. Unsure, we asked how to check it. "Remove the input shaft and count the teeth on the gear," he said. So Lamotta drained the transmission and removed the input shaft. Ours has 29 teeth.
The Centerforce DYAD DS clutch...
The Centerforce DYAD DS clutch has enough holding power to handle 750 lb-ft of torque, while maintaining stock driveability. Check back in the next few months as we upgrade our transmission, and install and test this unit.
Back on the phone with Walsh, we told him our findings. Cringing, he said "Yours has a 2.97 First Gear. If you had 31 teeth, it would mean you had a 2.66 First gear. We have 26-spline input shafts for the 2.66 First gear, but not for the 2.97 First."
Just to check, we called a few other places, including Tremec, and got the same answer. We could have one specially made, but that is expensive and time-consuming. On top of that, a simple input shaft upgrade would only remove the weakest link in the chain, and something else would fail instead.
Solution? Well, we're not sure yet, but we'll do something in the next couple of months, culminating in the installation of our new clutch and a track test. Stay tuned.

8 Part of replacing an engine...

8 Part of replacing an engine is replacing old, tired components. We couldn't recall the last time the spark plug wires were changed, so we ordered a set of Ford Racing wires from Brothers Performance (PN FOR-M-12259-R464; $109.99).

9 Ford Racing Performance...

9 Ford Racing Performance Parts sent us these new 34-lb/hr injectors (PN M-9593-LU34A; $319/set of eight). We requested 30s, but they have been discontinued, so we chose these. Also needed for our application were the adapters (PN M-14464-A8; $52.95/set of eight).

10 MPS Auto Salvage sent...

10 MPS Auto Salvage sent us the miscellaneous equipment necessary for the Mach 1 intake swap. It sent us the throttle cable, coolant crossover, and cruise control assembly to accommodate the relocation of our throttle body.

11 Brothers Performance also...

11 Brothers Performance also supplied us with this pair of Energy Suspension polyurethane engine mounts (PN ENE-4.1127G; $145.99). Our stock ones were original and in pretty bad shape.

12 We left the Moroso oil...

12 We left the Moroso oil pan from the engine dyno test in place.

13 Accufab sent us one of...

13 Accufab sent us one of its Mach 1 throttle bodies (PN CTB99-01; $389.99) to fit our intake manifold. This twin-60mm piece is milled from billet aluminum and also fits '99/'01 Cobras.

14 To complement all of our...

14 To complement all of our other new components, we contacted PA Performance for a 130-amp alternator (PN 1988; $259) and high-torque starter (PN 1799; $135).

15 Both the alternator (shown)...

15 Both the alternator (shown) and starter are direct replacements for the factory units, so no cutting, grinding, or welding is necessary.

16 Lamotta bolted the pump...

16 Lamotta bolted the pump in the stock location and wired it using the existing relay leftover from our nitrous system.

17 Meziere sent us an electric...

17 Meziere sent us an electric water pump (PN WP346S; $466.03), which pumps 55 gallons per minute. This will prevent a manual pump from robbing 10-15 hp from our bottom line.

18 He then concentrated on...

18 He then concentrated on the wiring harness. Since we are now using a Mach 1 intake manifold, the IAC and TPS pigtails needed to be lengthened. Lamotta did this and rewrapped the harness to make it look new again.

19 From below, you can see...

19 From below, you can see that our new American Racing Headers long-tubes and Moroso pan clear the stock K-member—barely. We could've used this opportunity to upgrade to a tubular K-member, but we're sticking with stock.

20 Cenerforce sent us one...

20 Cenerforce sent us one of its new DYAD twin-disc clutches, but it was equipped with a 26-spline disc. Our old T-56 has a 10-spline input shaft, so Lamotta reinstalled the old clutch for now. See the sidebar for more information on this.

21 Then Lamotta reinstalled...

21 Then Lamotta reinstalled the transmission.

22 Our exhaust kit from American...

22 Our exhaust kit from American Racing Headers (PN MSTE4V34WC; $1,494) comes with long-tube headers, high-flow catalytic converters, and an X-style mid-pipe--all made of 304 stainless steel.

23 Lamotta installed the...

23 Lamotta installed the remainder of the exhaust system, but the mid-pipe interfered with our transmission crossmember. He marked where it was hitting and trimmed the crossmember to accommodate the exhaust.

24 Here is the finished product....

24 Here is the finished product. We did lose our strut tower brace, and we had to grind a small dimple into the underside of the hood, but it fits.

The run in blue is our baseline....

The run in blue is our baseline. It only made 306 rwhp and 285 lb-ft of torque before breaking up at 5,500 rpm. After (in red), it made a best of 428 rwhp and 395 lb-ft of torque, thanks to a custom SCT tune by Chris Johnson.