Muscle Mustangs & Fast FordsHow To Engine
1993 Ford Mustang LX SSP Edelbrock Performer RPM II Install - The Strip Performer - Tech
We Picked Up 2 MPH And Shaved Over Two Tenths Off E.T.'S With Edelbrock's Performer RPM II On Our '93 SSP LX.
As a project progresses, it tends to take on a life of its own. This is exactly what has happened with our '93 LX SSP. From its early days of 14-second e.t.'s, it's sure come a long way to its current 11-second status. Meant to be an everyday driver with enough gusto for slaying Brand-X muscle, our coupe has stood up proudly as an all-around performer.
In the Oct. '10 issue, we installed a Zex nitrous system on our resident SSP coupe. On the dyno, the 125-shot translated into an 86 rwhp and 84 lb-ft of torque gain. Certainly a nice increase, but the dyno graph revealed that the output flat-lined at 5,000 rpm. Looking to free up power a bit higher in the rpm range, we called up Edelbrock for one of its Performer RPM II intake manifolds.
Designed with larger and shorter runners, the Performer RPM II (PN 71233) is engineered for optimal performance between 1,500 and 6,500 rpm. It will also clear our SSP's stock hood, and it just looks cleaner and meaner than our current Cobra intake. It even comes with a removable plate so we can port the runners if we want to later.
Best output prior was 344 rwhp and 361 lb-ft of torque on the Dynojet at Ramsey's Performance (Lutz, Florida). Since dropping the timing to 14 degrees to complement the nitrous, our LX's performance on the street was lacking, so we called Chris Johnson of SCT for some help. He showed up with an SCT multi-program switch chip for our EEC-IV ECM.
After maximizing power output both on and off the nitrous (without having to change the timing manually), we replaced the intake with the Edelbrock Performer RPM II. We also took this opportunity to readjust the rocker arms and replace the valve covers with matching black covers from Edelbrock.
As expected, we noticed a drop in lower-rpm power, but that was only when running NA. That's because the Edelbrock intake's larger runners were not as efficient as filling the cylinders down low, but it's a different story up high. In fact, the power was up by as much as 25 hp at 6,000 rpm! On the nitrous, power and torque were both up above 5,100 rpm, and our Performance Automatic torque converter was certainly going to help keep our coupe in its new higher power band on the track.
For our track test, we expected the best, but scorching heat and near 80 percent humidity kept the SSP from running to its potential. Once we let it cool in the staging lanes at Gainesville Raceway (back to ambient temperature of 96 degrees Fahrenheit), we opened the bottle and heated up the Mickey Thompson drag radials. The first hit yielded an e.t. of 11.55 at 117 mph-a best ever for the little coupe, and that was with our big front tires and the front antiroll bar connected. Unfortunately, mid-August heat and traction issues (due to our newly found power) prevented another 11-second timeslip, but we were satisfied with the results. Next time, we'll set up the LX a little better and we expect lower 11s to boot.
Though some power was lost down low, it wasn't enough to be noticeable on the street. As always, we'll continue to tweak our little coupe one story at a time, so check back next month to see what we've done. And if you have any suggestions for what we should do next, send an to email@example.com.
On The Chip
Once a staple of 5.0L tech, the "chip" (which plugs into the computer to re-tune the engine) has been all but forgotten. But that doesn't make its affordability and effectiveness any less desirable. SCT makes chips and tuning software for EEC-IV processors like ours, and it's a great way to get a little extra or do simple functions like raise the rpm limiter for not a lot of money. The chip itself (PN 6600) plugs directly into the ECM, is programmable with up to four different tunes, and retails for $269.