Muscle Mustangs & Fast FordsHow To Engine
2011 Ford Mustang 3.7L V6 Engine
Lighter, Smaller, And Far More Powerful Than The Old 4.0L, The New 3.7L V-6 Moves The 2011 Mustang Strongly Into The 21st Century.
The new valvetrain uses what Ford calls a megacap, a front cam bearing cap on each bank that manages oil flow to the variable cam-timing sprockets and down through the four hollow camshafts to the other cam journals and the rest of the valvetrain, a brilliant solution.
Under those two Nylon 6 noise-abating cam covers, the valvetrain uses very highly polished, mirror-finish, direct-acting bucket tappets between the camshafts and the valve tips, each one computer-selected for fit and clearance, a move that takes a tremendous amount of friction out of the valvetrain and accounts for almost a one percent fuel economy improvement all by itself. Using direct-acting bucket tappets instead of roller finger followers or single-overhead cams, like some other Ford engines, saved 30 mm in overall engine height, an important consideration for cars with low hoodlines.
Each hardened tappet has a very slight crown in the surface, about 15 microns from side to side, to work better against the surface and metallurgy of the drilled-out hollow camshaft's lobes.
Inside, the new engine uses piston-cooling oil jets mounted in the die-cast aluminum block that allows a higher compression ratio and a greater amount of spark advance for power production. With check valves in place, the cooling jets work only when the engine is hot and highly stressed. And, speaking of oil, you won't have to reach for the left-front-mounted oil filter or drain the sump of the die-cast deep-sump aluminum oil pan of its 5W-20 oil for 10,000 miles, a 33-percent improvement over the usual 7,500-mile interval. This is an advantage brought about by continuous analysis of driving cycles (Ford says almost all of its engines will be 10,000-milers by 2012).
The whole front-end accessory drive or FEAD has been redone in the conversion from east-west installation to north-south, so the engine now uses what Ford calls a stretchy FEAD, with no idlers or tensioners to rob power from the engine, for the air conditioning compressor, and a second belt and tensioner to drive all of the other pumps. The cooling system has been completely re-engineered to put the thermostat and water pump at the front of the engine, and the coolant fluid flow has likewise been re-engineered with a minimum of exterior plumbing.
Ford also worked outside the engine to make the package a better fit for the Mustang. The powertrain ECU has been upgraded with a very aggressive deceleration cylinder shutoff for fuel economy, coupled with very rapid tip-in for street performance. On the flip side, the ECU has been reprogrammed with adaptive-knock spark control. If the two knock sensors embedded in the cylinder block don't hear knocking, the ECU will keep advancing the spark until it does.
What this means in performance terms is that, if the owner uses premium or race gas on weekends, the engine should make considerably more power and torque than the numbers quoted here, which are the product of standard SAE dynamometer laboratory testing procedures and not real-world driving.
The new engine will be packaged together with either a six-speed MT-82 manual transmission with needle bearings on all of its shafts for friction reduction, or with a 6R-80 wide-ratio automatic transmission that will allow 7,000-rpm upshifts and torque converter lockup in Third through Sixth gears for improved fuel economy. Every 2011 V-6 Mustang will be sold with electric power-assisted steering (EPAS) for further fuel efficiencies, and Ford promises that the steering will be of a far sportier nature than other EPAS systems.
What's the next step? Well, give it a couple of years, and you will likely see an EcoBoost engine coming along, a twin-turbocharged, direct-injection version of this engine as a viable performance alternative to the current 4.6-liter V-8 engine.
The Wrapper It Comes In:
2011 Mustang Updates
The 2011 Mustang, while not all-new, will carry a host of improvements, upgrades, and updates inside and out. Outside it will have new blind-spot mirrors, 4-percent better aero performance around the nose, with a new underbody shield and wheel spats, and standard dual exhausts regardless of engine choice.
Underneath that shiny sheetmetal there will be chassis improvements, including stiffer suspension arms and bushings, larger front and rear stabilizer bars, rear wheelhouse liners for noise control, lower-rolling-resistance tires, the same brakes as the 2010 GT on the V-6 versions, a new Z-brace to reduce cowl shake, a standard strut-tower brace on all models, and electric power steering on all models for improved mileage and less drag on the engine.
Inside, there will be new rear headrests, more in-dash sound insulation, the addition of the MyKey option and new instrument panel graphics, and lighted visors with a new flexible storage system for sunglasses and other items. A new instant-start system requires one quick flip of the ignition key. Options will include a Pony package, a Mustang Club of America (MCA) package, and a Performance package consisting of GT suspension, upgraded brakes, 19-inch wheels and summer tires, and a looser yaw-control calibration.